USE OF ALARM SYSTEM TOYOTA RUSH
Wireless remote control system is designed to lock or unlock all locks and side door or back door alarm activate within a distance of approximately 10 m from the vehicle (without obstruction).
When you operate any switch, press it slowly and correctly. At this time the indicator light will illuminate when pressed (answerback).
Remote control is an electronic component. Consider the following guidelines to avoid causing damage to the remote control.
@. Do not leave keys in places where the temperature is very high as above the dashboard.
@. Do not disassemble.
@. Avoid impact against other objects or severe fall.
@.Avoid wet conditions or fall / dipped into the water.
You can use up to four remote control for the same vehicle. Contact your Toyota dealer to obtain detailed information.If you can not move the remote control doors or alarm, or can not be operated from the normal range or on a key indicator lights dim or no light, then:
Wireless remote control system is designed to lock or unlock all locks and side door or back door alarm activate within a distance of approximately 10 m from the vehicle (without obstruction).
When you operate any switch, press it slowly and correctly. At this time the indicator light will illuminate when pressed (answerback).
Remote control is an electronic component. Consider the following guidelines to avoid causing damage to the remote control.
@. Do not leave keys in places where the temperature is very high as above the dashboard.
@. Do not disassemble.
@. Avoid impact against other objects or severe fall.
@.Avoid wet conditions or fall / dipped into the water.
You can use up to four remote control for the same vehicle. Contact your Toyota dealer to obtain detailed information.If you can not move the remote control doors or alarm, or can not be operated from the normal range or on a key indicator lights dim or no light, then:
@. Check that adjacent transmitters such as radio stations or airports that may affect the normal remote control.
Tip: if this happens, hold the remote control on the windshield of the driver, then press the remote control switch for 3 seconds or until the lock or unlock the central lock.
@. The battery may have been empty, check the batteries in the remote control.
If you lose your remote control, immediately contact Toyota dealer to avoid the possibility of theft or accident.
Locking and unlocking doors
To lock and unlock all the side door and back door, press the key switches slowly and correctly.Locking the doors with the remote control will activate the alarm system and release the key will disable the alarm system.
Lock and alarm
Press the switch and make sure all the side doors and rear doors have been closed. All the side doors and rear doors will lock simultaneously. At that time, two indicators will appear as follows.
• Turn lights flashing signs at all.
• horn will sound once.
Check to find out that all the side doors and rear doors have been locked securely.To find out if there is one door or the hood is not closed properly, consider the following indicators.
If the door is still open / not tightly: the horn will beep 5 times, turn signal lights blink once and the alarm indicator LED blinks 3 times - 3 times onwards.
If the hood is open / not tightly: the horn will beep 5 times, turn signal lights blink once and the alarm indicator LED blinks 1 time - 1 time onwards.
If the switch is pressed when the ignition key in position "Lock or ACC, central lock will lock and the alarm is active.If the switch is pressed when the ignition key in position "ON, then the central lock will lock but the alarm will not be active.
If the alarm has been activated
When the alarm system to detect abnormalities will display the following indicators.
@. When the sensor gets collisions is, the alarm will sound a warning horn 10 times teputus-end and turn signal lights blink twice.
@. Sensor gets to the crunch. *
@. One of the doors or hood is opened by force. **
@. contact female friend turned to position "ON".
@. battery terminals or circuits connected to the ECU and then released again.*
The alarm will only receive the vibrations 3 times in 1 hour, 4 vibration to be ignored and returned to normal after 1 hour. This is to avoid continuous false collisions.
It rang for 30 seconds ** if either door is opened and then closed again and if it continues then the door is opened the alarm will sound for 30 seconds times 3.
If the battery is empty
When the battery is recharged or replaced, the system will sound an alarm. To stop the alarm press the switch of the alarm stops.
Lock and unlock the alarm without sound (silent mode)
Performed within 3 seconds.Press the switch and press it all the side doors and rear doors will lock simultaneously. Turn signal lights blink once.Description: make sure that all doors are closed tightly because this is not a warning.
Open and disable the alarm
Press the switch then all the side doors and rear doors will open simultaneously. At this time, there will be an indicator as follows.• Lamps turn sign blinks two times.• horn will sound 2 times.• LED indicator does not light. *
* If the flashing LED alarm indicator, this is to notice that the alarm had sounded and to determine the source of sounds refer to the table.
Open and disable the alarm without sound (silent mode)
Performed within 3 seconds.Press the switch and press it all the side doors and rear doors open simultaneously. Turn signal lights blink twice.Active system and lock the door automatically (auto re-arm / re-lock)The alarm is active and central lock will lock after 30 seconds, starting after we disable the alarm via the remote control but there are no doors are opened.
TABLE DIAGNOSTICS
If you lose your remote control, immediately contact Toyota dealer to avoid the possibility of theft or accident.
Locking and unlocking doors
To lock and unlock all the side door and back door, press the key switches slowly and correctly.Locking the doors with the remote control will activate the alarm system and release the key will disable the alarm system.
Lock and alarm
Press the switch and make sure all the side doors and rear doors have been closed. All the side doors and rear doors will lock simultaneously. At that time, two indicators will appear as follows.
• Turn lights flashing signs at all.
• horn will sound once.
Check to find out that all the side doors and rear doors have been locked securely.To find out if there is one door or the hood is not closed properly, consider the following indicators.
If the door is still open / not tightly: the horn will beep 5 times, turn signal lights blink once and the alarm indicator LED blinks 3 times - 3 times onwards.
If the hood is open / not tightly: the horn will beep 5 times, turn signal lights blink once and the alarm indicator LED blinks 1 time - 1 time onwards.
If the switch is pressed when the ignition key in position "Lock or ACC, central lock will lock and the alarm is active.If the switch is pressed when the ignition key in position "ON, then the central lock will lock but the alarm will not be active.
If the alarm has been activated
When the alarm system to detect abnormalities will display the following indicators.
@. When the sensor gets collisions is, the alarm will sound a warning horn 10 times teputus-end and turn signal lights blink twice.
@. Sensor gets to the crunch. *
@. One of the doors or hood is opened by force. **
@. contact female friend turned to position "ON".
@. battery terminals or circuits connected to the ECU and then released again.*
The alarm will only receive the vibrations 3 times in 1 hour, 4 vibration to be ignored and returned to normal after 1 hour. This is to avoid continuous false collisions.
It rang for 30 seconds ** if either door is opened and then closed again and if it continues then the door is opened the alarm will sound for 30 seconds times 3.
If the battery is empty
When the battery is recharged or replaced, the system will sound an alarm. To stop the alarm press the switch of the alarm stops.
Lock and unlock the alarm without sound (silent mode)
Performed within 3 seconds.Press the switch and press it all the side doors and rear doors will lock simultaneously. Turn signal lights blink once.Description: make sure that all doors are closed tightly because this is not a warning.
Open and disable the alarm
Press the switch then all the side doors and rear doors will open simultaneously. At this time, there will be an indicator as follows.• Lamps turn sign blinks two times.• horn will sound 2 times.• LED indicator does not light. *
* If the flashing LED alarm indicator, this is to notice that the alarm had sounded and to determine the source of sounds refer to the table.
Open and disable the alarm without sound (silent mode)
Performed within 3 seconds.Press the switch and press it all the side doors and rear doors open simultaneously. Turn signal lights blink twice.Active system and lock the door automatically (auto re-arm / re-lock)The alarm is active and central lock will lock after 30 seconds, starting after we disable the alarm via the remote control but there are no doors are opened.
TABLE DIAGNOSTICS
LED BLINK TOTAL HAS HAPPENED TO INTERFERENCE
1-------------- It has opened the hood
2---------------It has been one of the doors opened
3-------------- Getting harder collisions
4-------------- Additional sensors (if equipped)
5---------------Key contact once in the "ON"
LED will automatically return to normal when the ignition is in turn to the "ON"
Sounds an alarm (panic mode)
Pressing the switch for 2 seconds or more will honk the horn a halting vehicle and turn signal lights and turn on interior lights to blink.This function is used to deter theft of the vehicle when you see someone trying to break windows or damage your vehicle.Alarm will sound 30 seconds of immersion. To turn off the alarm before 30 seconds press the switch.Panic mode still works when the ignition is in position "ON".
Disabling an emergency (without remote control)
At the time the alarm is active and the siren went off while the remote control does not function in conditions.The alarm can be stopped by the way: turn the ignition from ACC to ON-OFF 10 times the siren will stop.
Central lock lock and unlock automatically
After the door is closed properly when the ignition is turned from ACC to ON then the central lock will automatically lock in 3 seconds later. Central Lock will re-open when the ignition is turned to OFF.Attention: The function lock will be canceled, after 1.5 seconds when the ignition is turned now to the ON position but there is still one of the doors are still not closed properly.
Bypass an alarm
Marked by alarm LED indicator lights illuminate.Useful to disable alarm functions work within the specified time as may be required, for example, the vehicle is doing service, laundry and others. But for the keyless entry, lock or unlock automatically and the alarm is still functioning.
How: Open one door and press the LOCK and UNLOCK and LOCK indicator LED alarm light will illuminate. To return to the Normal position, do the sam
2---------------It has been one of the doors opened
3-------------- Getting harder collisions
4-------------- Additional sensors (if equipped)
5---------------Key contact once in the "ON"
LED will automatically return to normal when the ignition is in turn to the "ON"
Sounds an alarm (panic mode)
Pressing the switch for 2 seconds or more will honk the horn a halting vehicle and turn signal lights and turn on interior lights to blink.This function is used to deter theft of the vehicle when you see someone trying to break windows or damage your vehicle.Alarm will sound 30 seconds of immersion. To turn off the alarm before 30 seconds press the switch.Panic mode still works when the ignition is in position "ON".
Disabling an emergency (without remote control)
At the time the alarm is active and the siren went off while the remote control does not function in conditions.The alarm can be stopped by the way: turn the ignition from ACC to ON-OFF 10 times the siren will stop.
Central lock lock and unlock automatically
After the door is closed properly when the ignition is turned from ACC to ON then the central lock will automatically lock in 3 seconds later. Central Lock will re-open when the ignition is turned to OFF.Attention: The function lock will be canceled, after 1.5 seconds when the ignition is turned now to the ON position but there is still one of the doors are still not closed properly.
Bypass an alarm
Marked by alarm LED indicator lights illuminate.Useful to disable alarm functions work within the specified time as may be required, for example, the vehicle is doing service, laundry and others. But for the keyless entry, lock or unlock automatically and the alarm is still functioning.
How: Open one door and press the LOCK and UNLOCK and LOCK indicator LED alarm light will illuminate. To return to the Normal position, do the sam
All New Avanza & The All New Avanza Veloz
0 komentar:
Post a Comment
please comment for an article on a blog entry http://toyotavanza.com. everything abaout avanzaku